Laatste nieuws van RepRapWorld

Creality has introduced this new version of the CR10, the V3 comes with an original e3d drive titan extruder. Unlike the V2 it can handle flexible filaments and has more power.  It has a build volume of 300x300x400mm and comes with a carborundum glass sheet for better adhesion. So if you are interested in printing with flexible filaments then click here and check it out because this could be the printer for you!

Ethernet Cat5e
You can now also purchase this Cat5e Ethernet cable in 0.5 meter  up to 30 meters in length. It has RJ45 plugs on both sides so it will fit on the Duet board, Raspberries and any other Ethernet capable device. Click here to find out all our available sizes.

Pre-cut flat ribbon cables
We now have our flat ribbon cables available in pre-cut sizes. They are gray, have a pitch of 1.27mm and are availabe in 10,25,50,100,150 and 200cm. Click here to purchase the size you are looking for.

Duet 3 Tool Distribution Board
With this new board you can connect up to 4 Duet 3 Toolboards to the Duet 3 mainboard at one time! It has a 2-way barrier strip for Power in, four 2-way JST VH connectors, two RJ11 connectors for CAN bus in/out , four 4-pin JST ZH connectors, four pairs of 2-pin headers and a CAN bus termination 2-pin header. Want to know more about this amazing board then click here!

Rotating Magnetic Filament Monitor
We now have the Duet 3D filament monitor. You can connect it to your Duet 2 or 3 and it can detect multiple issues like:

• Filament run out
• Extruder skipping steps
• Nozzle starting to jam
• Filament beginning to grind in the extruder

The magnet rotation is sensed and constantly reported to Duet board what makes this monitor extremely accurate for a wide range of filaments.  Click here to find out more!

Duet 3 Toolboard 1LC
This new Toolboard works with the Duet3D Mainboard. It is a CAN-FD connected expansion board  that is designed to provide complete control for a direct drive extruder. You can fit the E3D Hemera  on there, however it can be used with other direct drive extruders with suitable brackets too. You can connect the stepper motor, heater, temperature sensor, fans, filament monitor and optionally Z probe to this Toolboard what will result that only the CAN-FD and power wires run back to the Mainboard or Distribution board.
Want to find out more about its main features and the optional connector pack of this great Toolboard? Then click here!

Duet 3 Mini 5+
We now have the Mini 5+ in our assortment this slimmer version of the Duet 3 board is available in a Wifi and Ethernet version. IT is suitable for most 3D printers and upgradable with many available Duet 3 addons.

The board has a 32-vit ARM processor, provides 5 on-board drivers and has the normal complement of heater, fans, IO, LCD etc. This board has the option of using an SBC (Single Board Computer) for control in the same manner as other Duet 3 main boards. This Mini 5+ has a lot to offer you in it's small size, click here for the Wifi version and here for the ethernet one to find out more!

We have expanded our own branded popular PETG filaments. Already in our assortment were the Black and White 1.75mm, and now we also have 2.85mm available. Next to that we have added Light Green, Yellow, Red, Blue, Gray and Silver in both diameters. PETG is now available in the most popular colours and thanks to the economic packaging we can offer this great value filament for a great price. Go check it out now.

Next to expanding our PETG filaments we also added new colours and diameters to our ABS assortment. Black and White is now available in 1.75mm and 2.85mm and Yellow, Orange and Silver are available in 1.75mm. This great value ABS is excellent for prototyping and is available at a great price point. Go check it out now.

Click here to check out our own branded RepRapfilaments

After almost two years of waiting, the Snapmaker 2.0 is finally here and not just in one size, but three different models to suit all makers' needs! Each have the power to do 3D printing , cnc carving and laser engraving. It has automatic bed leveling, a filament detection sensor and a hotend that can go up to 275 degrees Celcius. For the CNC carving it comes with a 50W spindel and it is suitable for many different materials like wood and acrylic. The laser part of this printer is also fantastic with is powerful 450nm 1600W laser and the built-in camera that will give you the ability to see a preview of your design. You can edit and position your project however you want. The Snapmaker 2.0 comes with a 5" smart touchscreen and is easy to assemble.

These are the three models:

A150 
Printer volume: 300x316x390mm
3D printing volume: 160x160x145mm
CNC milling volume: 160x160x90mm
Laser engraving volume: 160x160mm
Heated bed temp: up to 110 degrees Celcius

Click here to find out more about this printer!

A250
Printer volume: 405x424x490mm
3D printing volume: 230x250x235mm
CNC milling volume: 230x250x180mm
Laser engraving volume: 230x250mm
Heated bed temp: up to 100 degrees Celcius

Click here to find out more about this printer!

A350
Printer volume: 495x506x580mm
3D printing volume: 320x350x330mm
CNC milling volume: 320x350x275mm
Laser engraving volume: 320x350mm
Heated bed temp: up to 80 degrees Celcius

Click here to find out more about this printer!