Deals will end in:
  • Dagen
  • Uren
  • Minuten
  • Seconden

Megatronics v3.3 - Delta kit

SKU:MEGATRONICSV3KOSSL
GTIN:8719128327822
Voorraad: 16
€ 205,75  incl BTW Op voorraad
Zelfde werkdag verzonden!

Productbeschrijving

The new powerful electronics for any RepRap!

Megatronics is based on many famous open-source products including: Arduino Mega, RAMPS, SD Ramps. Therefor this product is an already proven design. It combines all major features of these board into a single board solution for more reliable 3D-printing. This board will get you the most features for the best price! 

Megatronics has a powerful Atmega2560 processor with 256 kB memory, running at 16Mhz. The board can be connected to a PC using a normal USB cable. It will register as FTDI FT232R device. The board is compatible with the Arduino Mega 2560 and will therefor be easily programmed from the Arduino IDE.

This is only the board. Stepper drivers are not included.

Major features

Atmega2560
Powerful Atmega2560 processor with 256 kB memory, running at 16Mhz

Thermo couple (2x)
On board support for connecting two thermo couples

SD Card
Autonomous printing from Micro SD card on board, also an external SD card is supported

LCD support
Hooking up a LCD is pretty easy. The Wiring is compatible with most LCD screens. We do not sell the required wiring yet, but you can use 6x2-wire cable.

Six MOSFETs
The board has 3 MOSFETs (3x 25A) to support  extruders, 2 MOSFETs fior fans and 1 MOSFET (IRLS3034PBF) for the heated bed

Four thermistors
Four thermistors are supported.

Up to 6 stepper drivers
Compatible with RAMPS, 6 slots for stepper drivers (not included). Modularized to make replacement easy for damaged drivers. This board also support the new DRV8825 driver from Pololu http://www.pololu.com/catalog/product/2132.

Support for many peripherals
The board's functions can be easily extended with LCD, keypad etc. See the connectors section for more information

Other features

  • USB 2.0 Full Speed compatible
  • Auto reset can be disabled by removing a jumper
  • The board can be powered from 12V1 (12V MAX), by setting a jumper
  • The LCD contrast can be adjusted with a trimpot
  • The 5V line is protected by a 500mA resettable fuse
  • A piezo is included to allow the printer to give feedback with sound
  • Each stepper driver slot has a breakout to connect external stepper drivers to the board.
  • Four layer high quality PCB board

Board dimensions

Width: 109.5mm
Length: 90.5mm
Height: 18mm

Datasheet: Coming soon
Marlin firmware: See download section (service -> software downloads)

 

€ 205,75  incl BTW Op voorraad
Zelfde werkdag verzonden!

Prijsstaffel

1 - 9: excl € 170,04 incl € 205,75
10 - 29: excl € 161,54 incl € 195,46
30 - : excl € 153,04 incl € 185,17
Groter aantal nodig? Neem contact op met Verkoopafdeling.

Over ReprapWorld
ReprapWorld

RepRapWorld is de nummer één webshop voor al uw reprap benodigdheden voor uw 3D printer. We hebben een grote collectie 3D-printer onderdelen, van onze beroemde elektronica lijnen tot filament van onze eigen productie. En dit alles aan een zeer scherpe prijs!

Contact

RepRapWorld B.V.
Klopperman 7
2292JE Wateringen
The Netherlands

Email: info@reprapworld.com
Tel: +31 (0) 85 - 009 15 31

Copyright 2009 - 2020 | ReprapWorld B.V.