Megatronics v3.3 - Basic kit

Voorraad: 0
€ 120,99  incl BTW
Verwachte levering binnen 1 - 2 weken


Megatronics, including stepper drivers

Megatronics is based on many famous open-source products including: Arduino Mega, RAMPS, SD Ramps. Therefor this product is an already proven design. It combines all major features of these board into a single board solution for more reliable 3D-printing. This board will get you the most features for the best price! 

Megatronics has a powerful Atmega2560 processor with 256 kB memory, running at 16Mhz. The board can be connected to a PC using a normal USB cable. It will register as FTDI FT232R device. The board is compatible with the Arduino Mega 2560 and will therefor be easily programmed from the Arduino IDE.


Major features

Powerful Atmega2560 processor with 256 kB memory, running at 16Mhz

Thermo couple (2x)
On board support for connecting two thermo couples

SD Card
Autonomous printing from Micro SD card on board, also an external SD card is supported

LCD support
Hooking up a LCD is pretty easy. The Wiring is compatible with most LCD screens. We do not sell the required wiring yet, but you can use 6x2-wire cable.

The board has 3 MOSFETs (3x 25A) to support  extruders, 2 MOSFETs fior fans and 1 MOSFET (IRLS3034PBF) for the heated bed

Four thermistors
Four thermistors are supported.

Up to 6 stepper drivers
Compatible with RAMPS, 6 slots for stepper drivers (not included). Modularized to make replacement easy for damaged drivers. This board also support the new DRV8825 driver from Pololu

Support for many peripherals
The board's functions can be easily extended with LCD, keypad etc. See the connectors section for more information

Other features

  • USB 2.0 Full Speed compatible
  • Auto reset can be disabled by removing a jumper
  • The board can be powered from 12-24V
  • The LCD contrast can be adjusted with a trimpot
  • The 5V line is protected by a 500mA resettable fuse
  • A piezo is included to allow the printer to give feedback with sound
  • Each stepper driver slot has a breakout to connect external stepper drivers to the board.
  • Four layer high quality PCB board

Board dimensions

Width: 109.5mm
Length: 90.5mm
Height: 18mm

Datasheet: Coming soon
Marlin firmware: See download section (service -> software downloads)



Technologie AVR
Type Atmega2560
Frequentie 16 MHz
Geheugen 512
Lengte 110 mm
Diepte 95 mm
Hoogte 18 mm
Thermistoren 4
Eindstops 6
Stappenmotordriver 6
Thermocouples 2
Keypad connector
Externe SD-kaart
Externe stappenmotoren aansturing 6
Gescheiden invoer voor verwarmd bed
€ 120,99  incl BTW
Verwachte levering binnen 1 - 2 weken


1 - 9: excl € 99,99 incl € 120,99
10 - 29: excl € 94,99 incl € 114,94
30 - : excl € 89,99 incl € 108,89
Groter aantal nodig? Neem contact op met Verkoopafdeling.


Gerelateerde producten die passen bij de Megatronics v3.3 - Basic kit.

Keypad v1.0 - Fully Assembled
  € 18,25
LCD - 20X4 - blue/white
  € 20,50
Thermocouple cartridge K-type (1M)
  € 12,75

Over ReprapWorld

RepRapWorld is de nummer één webshop voor al uw reprap benodigdheden voor uw 3D printer. We hebben een grote collectie 3D-printer onderdelen, van onze beroemde elektronica lijnen tot filament van onze eigen productie. En dit alles aan een zeer scherpe prijs!


RepRapWorld B.V.
Klopperman 7
2292JE Wateringen
The Netherlands

Tel: +31 (0) 85 - 009 15 31

Copyright 2009 - 2021 | ReprapWorld B.V.